Up English Deutsch Français Information Feedback[Company Logo Image]

Installation
µPREMIUM-MFS Installation

 

 

 

 

Installation instructions for µPREMIUM-EM and µPREMIUM-MF

If the mounting plate is used, the reader cable may be brought out of one of four exit points on the mounting plate: top, bottom, left or right. This enables the cable to be run on the surface of the wall. 

If no mounting plate is used, a minimum hole size of 6,5 mm must be drilled in the wall at the cable exit position as shown above to allow the cable to exit perpendicular to the reader.

The optional mounting plate may also be used when mounting the reader on a metal surface to reduce the negative effects of metal on the read range.

Connections

Colour

Name

Function

BLACK

0V

Connect 0V from power supply. 

RED

+VDC

Connect +5V - +13.6V from power supply

PURPLE

RS-232 TX

Output RS-232

BLUE

BUZZER

Controls Buzzer 

GREEN

GRN-LED

Controls Green LED in LED Mode 1 or both Red and Green LEDs in LED Mode 2

ORANGE

RED-LED

Controls Red LED in LED Mode 1

YELLOW

YEL-LED

Controls Yellow LED in LED Mode 1

BROWN

DATA / DATA1

Outputs RFID tag code in selected format

WHITE

CLOCK / DATA0 / TTL-TX

Outputs RFID tag code in selected format

GREY

CARD PRESENT

Pulses low when an RFID tag is detected. It stays low while the module output is active

Note : LED and BUZZER inputs are active low. The input is internally pulled high and may be pulled low by an open collector transistor or driven low by the output of a 5V CMOS or TTL gate.

Output mode selection

The 6-way switch is used to select the output format and LED mode. The required setting is selected from the following tables:

 Output mode table

SW1

SW2

SW3

SW4

Output mode

ON

ON

ON

ON

Inhibit – Turn off coil

ON

ON

ON

OFF

Not used

ON

ON

OFF

ON

Not used

ON

ON

OFF

OFF

Not used

ON

OFF

ON

ON

Not used

ON

OFF

ON

OFF

RS232 – 2400,n,8,2

ON

OFF

OFF

ON

RS232 – 4800,n,8,2

ON

OFF

OFF

OFF

RS232 – 9600,n,8,1

OFF

ON

ON

ON

Clock/Data 8 characters

OFF

ON

ON

OFF

Clock/Data 9 characters

OFF

ON

OFF

ON

Clock/Data 10 characters

OFF

ON

OFF

OFF

Clock/Data 13 characters

OFF

OFF

ON

ON

Not used

OFF

OFF

ON

OFF

Wiegand 26 bits

OFF

OFF

OFF

ON

Wiegand 34 bits

OFF

OFF

OFF

OFF

Wiegand 42 bits

 LED mode table

Mode #

SW5

LED Mode

1

ON

3 Individual LED’s each controlled by their own input

2

OFF

RED/GREEN with single control line (GRN-LED)

Note : In LED Mode 2, both RED and GREEN leds are controlled by the GRN-LED input. When the GRN-LED input is floating or pulled high, the RED led is on and the GREEN led is off. When the GRN-LED input is pulled low (connected to 0V) the GREEN led is on and the RED led is off. The YELLOW led is always off.

Continuous/Single Transmission Mode Table

Mode

SW6

Operation

Continuous

ON

While a tag is in the reader’s field the reader will continuously transmit the code in the format chosen by DIP-switches 1-4. The repetition period is dependent on the format chosen but varies between 65ms and 100ms.

Single

OFF

Single transmission when tag is brought into the field. Tag must be removed from field for at least 1 second before a read of this tag is possible again.

 

Note : this “continuous transmission” mode can not be guaranteed to work properly on some controllers, depending on the data interfaces. However, the “single transmission” mode will work with all controllers. It is therefore recommended to test this function prior to site activation.

Power Connections

The reader has an internal low dropout 5V regulator and so for maximum performance the input voltage must be smooth DC between 5.5V and 13.6V. The reading distance is unchanged for input voltages between 5.5V and 13.6V. For input voltages below 5.5V the read range drops off slightly as given in the specifications earlier. If 5V is supplied to the reader this should be noise-free to achieve maximum possible read ranges.

Note that the read range will increase if the input voltage increases.

Tuning the antenna

Under the front cover is a variable capacitor, which may need to be adjusted to re-tune the antenna in different environments.  To tune the antenna, switch SW6 on (continuous mode).  Now put a card in the field and adjust the variable capacitor until the unit is beeping repeatedly (beep...beep...beep...beep...).  The best tuning is when the gap between beeps is shortest.

 

 

Contact Information

 

Head office

 

 

 MicronID Development Ltd,  Digeni Akrita 46-3/31, 1061  Nicosia, Cyprus

Tel.: +357 (0)22 458 954   Fax : +357 (0)22 458 715   E-mail : info@micronid.com

VAT n° : CY 101.667.76Z        Reg. n° : HE 166776

 

Send e- mail to info@micronid.com with questions or comments about this web site.
Copyright © 2008 MicronID Development Ltd